Skip to main content
Topic: Chuck's '83 TBird (Read 40995 times) previous topic - next topic

Re: Chuck's '83 TBird

Reply #240
Nice job on the line bracket and a big congrats on the new addition to the family!
1985 Mercury Cougar XR-7 - 5-speed 
One of 1,246 built

Re: Chuck's '83 TBird

Reply #241
Congrats on #2!   Bracket looks good too!
84 COUGAR/90 HO, 1.7RRs, performer RPM,700DP, equal length shorties, stainless EXH ,T-5,Hurst pro-billet, KC clutch, 8.8/ 4.10s, line-lok, bla ,bla, bla.
71 COMET/289,351w heads, 12.5 TRWs, 750DP, Liberty TL, 9"/6.00s, 11.9x @112 , bla,bla,bla.

Never shoot your mouth off, unless your brain is loaded! ....I may get older, but I'll never grow up!....If you're not laughing, you're not living!  :laughing:

 

Re: Chuck's '83 TBird

Reply #242
Congrats on baby #2!
1988 Thunderbird TC, 5spd
Stinger single exhaust, Cone Filter, Adjustable Cam Pulley, Ranger roller cam conversion,
'93 Mustang Cobra replica wheels on 235/50R17

'16 F150 XLT 5.0
'17 Husqvarna TX300

Re: Chuck's '83 TBird

Reply #243
Congrats!

Time to teach baby #1 to weld.
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Re: Chuck's '83 TBird

Reply #244
Oh, hey. Look at this.



And it's under the car!


Long live the 4-eyes!  - '83 Tbird Turbo

Re: Chuck's '83 TBird

Reply #245
Looks great!
88 Thunderbird LX: 306, Edelbrock Performer heads, Comp 266HR cam, Edelbrock Performer RPM intake, bunch of other stuff.

Re: Chuck's '83 TBird

Reply #246
Nice work fabricating those clamp-on axle brackets!  :bowdown:
1988 Thunderbird
306 HO w/ A9P processor
AOD w/ Transgo Reprogrammer
Full Digital Dash w/ twin Cyberdyne A-pillar gauges 
245/50/16 Tires on Snowflakes
Engine swap - CA smog compliant

Re: Chuck's '83 TBird

Reply #247
Nice work fabricating those clamp-on axle brackets!  :bowdown:
Wish I could take credit for those, but those are part of that Steeda kit that I cut apart to fit in here.

Not many updates this week. Been wrangling other projects, and time is limited.
Long live the 4-eyes!  - '83 Tbird Turbo

Re: Chuck's '83 TBird

Reply #248
Well, I managed to get the other car projects taken care of and was able to steal away a few hours this week to get some things done on this.



Got all of the new power stuff and lighting wiring sorted and tucked away. The lone orange wire is for the switch for the fog lights. I need to move a few things around to be able to open the 47'-long doors on this thing to work under the dash before I can finish that.
I'm probably going to make a little cover to hide a bunch of that wiring. There is just A LOT going on there on these cars...and I added more.

Got all of the new lights in place also.



Then I went to the back of the car to start to try and fish the tailpipe around everything.




There is a bunch of stuff to work around back here...especially with a 3" tailpipe.

I have a plan, but it needed to start with this.


Probably going to take another whack at the tailpipe and make a few other choice cuts to snake around all of the mess.
Luckily, I have a bunch of tubes on-hand. (This is all for the 240, but I can always buy more ;) )


I'm going to need to add a new bung for the WBO2 in the DP, and I think I may work in a couple more v-band clamps to make things easier to remove/fit.

Once it's all redone, I'm hoping my buddy can spray it with some Cerakote, like he did for my 850 exhaust.


Long live the 4-eyes!  - '83 Tbird Turbo

Re: Chuck's '83 TBird

Reply #249
This showed up today.


I already have a spare LSU 4.9 sensor in the garage, so I just need to get it into the exhaust and wired up.
Long live the 4-eyes!  - '83 Tbird Turbo