Skip to main content ↑ ↓
Topic: My 88 Sport (Read 1524 times) previous topic - next topic

My 88 Sport

Welp, I think I've gathered enough parts to start a build thread. Picked up the few major parts that were holding me up and my cowl scoop from Unlimited Products came yesterday (chipped corner, but I'm not going to waste time with returning it and waiting). I'm mainly focusing on the exterior so I can get on the road.
This winter I'll worry about the interior and engine bay.
Here's some pics...
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

My 88 Sport

Reply #1 –
Some more...
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

My 88 Sport

Reply #2 –
And...
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

My 88 Sport

Reply #3 –
..................and so it begins...................

Good luck.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

My 88 Sport

Reply #4 –
Thanks Vinnie. I'm so excited !!!
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

My 88 Sport

Reply #5 –
I was to when I first started the Sport,and now,after a LOT of work,I'm still excited to work on it (when I want to,not when I HAVE to.LOL). I was just telling Gayle last night when we were down town that I never get tired of that car.She was griping at me about getting the a/c installed stat.I'm going to wash and wax it today,then install the roller rockers on Sunday more than likely.From there.....we'll see.Funds are at a low point again after getting the rockers and new fuel pump.

Get started,and post pics.Do it right the first time.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

My 88 Sport

Reply #6 –
I might have some more center console pieces for ya if you want them. I'll have too look through some of my boxes of stuff but I'm almost positive I have a black switch panel. I'll let you know if I find'em.

Cant wait to see her with some color on her!
85 Tbird 5.0
78 F150 351w
13 F150 4x4 3.5 Ecoboost

My 88 Sport

Reply #8 –
Quote from: 88FoxBird;322824
I might have some more center console pieces for ya if you want them.
Cant wait to see her with some color on her!


That would be great !
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's

My 88 Sport

Reply #9 –
Quote from: 1 BADBIRD;322831
Man that will be one cool ride . Your cowl will look awesome with the coupe scoops in it . Keep posting pics , we love pics !!


Yeah, don't know where I got the inspiration for that :D
88 Sport ,306 roller block, flat tops, ARP rods and bolts, Compcam 533 lift/ 270 duration, roller rockers, ported 351w heads with 1.94 - 1.60 valves, 550 springs, 600cfm carb , full length headers, 2.5" dual X-pipe exhaust, MSD ignition, Hughes built C4, Weld Draglites, Tracloc /Richmond 3:73's