Type 6 (86+ 5.0) Poly Motor Mounts

Topic: Type 6 (86+ 5.0) Poly Motor Mounts (Read 14053 times) previous topic - next topic

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #120 – December 19, 2010, 09:33:53 AM

Quote from: 20thanniver-ls;346199

I'll have to take a peek at mine, and compare them, just figured you may have known off-hand.

I just can't recall any Mk7 guys picking them up. I would think that yours would be the same as the 5.0 87 Tbird/Cougar. If you can snap a quick pic or two from below, I could better help ID them.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #121 – December 19, 2010, 08:11:18 PM

OK, a quick part number search shows that for your '87, you would use the same mounts as an 87 Mustang.

If you want to snap a picture, I can verify it for you.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #122 – December 19, 2010, 09:51:11 PM

I got a few pictures, but I can't upload them, my sd card reader is missing.... I did a parts number search in relevance to the t-bird, and they were indeed different. I can try to grab some pics with my phone, but I have no flash so they may not be all that great.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #123 – December 21, 2010, 07:10:58 PM

Quote from: Chuck W;346272

OK, a quick part number search shows that for your '87, you would use the same mounts as an 87 Mustang.

If you want to snap a picture, I can verify it for you.

Yep the Mark VIIs use the same mount as 5.0 Mustangs. I believe they actually used the Mustang convertible mounts which are some what different (not much) than the hard top mounts.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #124 – December 27, 2010, 02:03:44 AM

Hey Chuck do your mounts sit same as factory? or lower? I have "altered" stock mounts a now my steering shaft ishiznitting the BBK longtubes. Mine are solid but I need some that sit the engine a tad lower? thanks

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #125 – December 27, 2010, 02:06:26 AM

no i am wrong motor need to go up a tad, mine are stocker drilled with a welded blolt through them. i think the lost some height

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #126 – December 27, 2010, 07:58:47 AM

They sit normally at around the stock height. You can space them up a slight bit (1/4-3/8") if needed with the stock hardware.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #127 – December 27, 2010, 11:57:48 PM

do you have any on hand? and if you do how much are they shipped to 61073. I just want the headers to clear

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #128 – December 28, 2010, 11:14:38 AM

I just sent out the last set I had on hand, so I would need to weld up and coat more.

They run $175/shipped in the US.

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #129 – March 22, 2014, 12:32:18 PM

I have a couple sets of my Type 6 motor mounts available at the moment. Coated black.
They will fit 5.0/5.8 motors into 86-97 TBirds/Cougars.

They run $175/shipped in the US.

Also, please don't ask about shock mounts in this thread. IF I decide to do more, I will post up about it.

Email me please at cwarren@indy.net

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #130 – March 26, 2014, 11:52:48 PM

One set still available

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #131 – March 27, 2014, 12:38:57 AM

I really should get these. monies

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #132 – March 27, 2016, 08:05:28 PM

So, I've been talked into doing a few more mounts (Been trying to take a break from it). I'm going to have a couple sets of Type 6's available in this batch.

Pricing as usual, $175/shipped in the US. Black powdercoat. Email me if you're interested at cwarren@indy.net.

(Sorry...no shock brackets will be happening)

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #133 – April 10, 2016, 06:24:17 PM

OK, well I'm welding these up right now. Get 'em while you can!

Type 6 (86+ 5.0) Poly Motor Mounts

Reply #134 – April 11, 2016, 01:03:46 AM

I have 351w in my 83tb, with convertible mustang mounts, you have mounts for 351w? benefit from the convertible style mounts?