Skip to main content ↑ ↓
Topic: aluminum drive shaft (Read 503 times) previous topic - next topic

aluminum drive shaft

See: http://www.foxtbirdcougarforums.com/showthread.php?31393-fms-140-aluminum-d-s-and-manual-seat-track&p=360355#post360355


admin, feel free to delete this. I added other stuff, it will be easier to mannage

aluminum drive shaft

Reply #1 –
That's a good deal. Shipping one really doesn't cost that much. We used two long narrow boxes (to make one longer box) wrapped it bubble wrap and shipped it. Less than $30.00 a little over a year ago.
'88 Sport--T-5,MGW shifter,Trick Flow R intake,Ed Curtis cam,Trick Flow heads,Scorpion rockers,75mm Accufab t-body,3G,mini starter,Taurus fan,BBK long tube headers,O/R H-Pipe, Flowamaster Super 44's, deep and deeper Cobra R wheels, Mass Air and 24's,8.8 with 3.73's,140 mph speedo,Mach 1 chin spoiler,SN-95 springs,CHE control arms,aluminum drive shaft and a lot more..

aluminum drive shaft

Reply #2 –
To short for me or I'd get it
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

aluminum drive shaft

Reply #3 –
What length do you need, and yeah vin I saw that post which is why I decided to ship too.

aluminum drive shaft

Reply #4 –
So it may have been used?
[SIGPIC][/SIGPIC]88 TBird-5.0 Cobra engine, Fresh Paint, BBK Cold Air Intake, Aluminum Driveshaft, Brian Crower Cam, Nitrous, 5 lug conversion, full cobra breaks/rims assembly, BBM shift kit, Maximum Motorsports Caster cambers/shocks/struts, Eibach Springs, Mass Air Flow Conversion, HEI Distributor, Compression rate 10:1, 2.25" dual Magnaflow glasspacks- Ford Motorsports short headers, 70 mm tbody/egr/upper, 1 inch spacer on manifold & more

aluminum drive shaft

Reply #5 –
So it may have been used on the previous car, but just for a short time? Meaning it's pretty new?
[SIGPIC][/SIGPIC]88 TBird-5.0 Cobra engine, Fresh Paint, BBK Cold Air Intake, Aluminum Driveshaft, Brian Crower Cam, Nitrous, 5 lug conversion, full cobra breaks/rims assembly, BBM shift kit, Maximum Motorsports Caster cambers/shocks/struts, Eibach Springs, Mass Air Flow Conversion, HEI Distributor, Compression rate 10:1, 2.25" dual Magnaflow glasspacks- Ford Motorsports short headers, 70 mm tbody/egr/upper, 1 inch spacer on manifold & more

aluminum drive shaft

Reply #6 –
Quote from: Nate;360259
What length do you need, and yeah vin I saw that post which is why I decided to ship too.

Mine is 48" C to C and Id like 49"1/2
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

aluminum drive shaft

Reply #7 –
Quote from: treflipboy;360268
So it may have been used on the previous car, but just for a short time? Meaning it's pretty new?

Yeah I think (99% sure) 1 or 2 dyno pulls and getting it on/off the trailer. so less then a mile? It defenatly looks new.