Skip to main content
Recent Posts
21
Drivetrain Tech / Re: Axle swap
Last post by Chuck W -
Looking a the axle chart listed in the pinned thread in this section (HERE

I have postulated that MAYBE you could use the 99-04 axles and brake set up on your wide 7.5 housing in your Sport. The numbers are really close. At least according to the chart.

You would need to swap to the rear discs though, and your flange to flange width would be 1.5" wider.
This is all just a guess though.

If you're keeping the drums, you'll need to either have your current axles converted to 5-lug or buy new, custom ones and use some Ranger drums.

94-98 Axles won't work in your wide housing. The bearing surfaces are in the wrong location. If your car was an 83-85, you'd have the narrow housing that would work with the 94-98 axles.

22
Drivetrain Tech / Re: Axle swap
Last post by Beau -
Yup, what Darren said. I know it sucks, but really, any rear from '94-98 will yield the axles you want. AFAIK, the brakes are the same across all those years, so what you already have harvested will do for you. (I'd probably spring for remanned rear calipers, when those shits seize, they're a pain, unless you have the stuff to take 'em apart and know how)..

I had/have what amounts to the same setup on both my Thunderbird and now on my '87 Mustang. Up front is the dual piston calipers,

On my 'Bird I had a bastard setup....used the stock Tbird Sport's backing plates, '97 Stang V6 axles (again, no matter if it's V6 or V8, the shafts themselves are the same), but I kept that car drums, and used Mercury Marquis drums, these were 10" drums and not the usual 9". With that setup, I HAD to have the Sport's back plates, all others were 9" drums, so....there's *probably* a way, but with all the Mustang shit in the yards now, no reason not to step up to dscs. I just did it to see if it could be done.

Now in my Mustang, I ran Ranger axles and kept the stock drums. There was no way to make a hybrid system as the axles are too short for that setup.

When I get the T5 rebuilt, I'll probably be swapping to discs and throwing a 3.73 in with a new Trac Lok.


BTW, if you've not ran the PBR calipers yet, holy shit, you'll feel like you're going to leave your teeth in the steering wheel.. LOL
23
Drivetrain Tech / Re: Axle swap
Last post by Aerocoupe -
Nope.  You need the 94-98 axles to keep the stock flange to flange measurement.  The front brakes are a nice upgrade being they have the dual piston caliper.  If you snagged the spindles they are not ideal on a stock k-member car due to their geometry but that can be dealt with via a bump steer kit.  I opted to go with the 96+ spindles on my stock k-member car as I knew a tubular k-member was going to happen and did not want to try and scrape up a set of the 94-95 spindles.

You do realize that the 94-98 GT and V6 cars have the exact same brakes, right?  In the rear the axles, brackets, dust shields, and calipers are the same.  Only difference is the housing in that one is for the 7.5 ring gear and the other is for the 8.8 ring gear.  As for the front they are straight across the same.  I pulled both my swaps from V6 cars being I already had the 8.8 housings and was converting from drum brakes.
24
Drivetrain Tech / Axle swap
Last post by count -
OK I know this horse been beat to death but let’s beat it a different way.  I recently want to a u pull it salvage yard I spent the day collecting calibers rotors brackets spindles hubs I guess you can see where I’m going with this yeah I was collecting for a 4-5 lug conversion it was going good until when I realized Man these axles are a little bit long.  this mustang is not the 96 8.8 V8 I came for but the 1999
Why I didn’t notice the Dual caliber, I don’t know.
But my question is can I still use this axles (30.75)length in my 88 sport.  ( the salvage yard combined with hour drive I would rather not make that trip again if I don’t have too plus a lot of seized bolts)
25
User Rides / Re: Starting fresh
Last post by Clayton -
Cars and coffee this morning, I got there pretty early but there were over 100 cars out there today. It was crazy.
26
User Rides / Re: 84 Tbird project
Last post by Beau -
GT40 heads are a nice improvement over the E7s, but I'll use aftermarket aluminum heads next time I put together a windsor based Ford. (leaning to a 32v and getting my feet wet in that bigger, deeper pool).

Car looks, you've done a hell of a lot. Enjoy it!
29
User Rides / Re: 84 Tbird project
Last post by Mikey97D -
Must be getting excited to put everything together.

What size valves are in the heads?  Any porting work done?
30
User Rides / Re: 84 Tbird project
Last post by 5.0 tbird -
Picked up my GT40 heads from the machine shop today! I had them rebuild the heads and install a Trick Flow spring kit.















I also got my gears installed a few weeks ago. Going from 2.73 to 3.73s was exactly what this car needed. The shop said it wouldn't cost any extra labor to rebuild my trac-lok while they did the gear swap so I bought a clutch kit.





After I got the car back from the shop I swapped out the speedo gear



So next up is upgrading the front brakes and putting the heads on.