Skip to main content ↑ ↓
Topic: Carbueted Hood clearance ? (Read 2091 times) previous topic - next topic

Carbueted Hood clearance ?

Can you carburetor guys tell me what intake you run and how much hood clearance you have?

Carbueted Hood clearance ?

Reply #1 –
Old performer with a motor sport 13" drop base air cleaner. Leaves about an inch between the hood and 3"filter
[SIGPIC][/SIGPIC]:ford:87 Turbo Coupe through the floor sub frame connectors, 5.8 swap Ford racing heads Harland sharp 1.6 rockers BBK shorty swap headers 2 1/2 BBk X pipe magnaflow ler's. Megasquirt 2 with 36lbs injectors on hurricane intake with 4150 throttle body.Tremec TKO 600 Quicktime blowsheild spec stage 3 clutch. 3.73 gears and still not done

Carbueted Hood clearance ?

Reply #2 –
Edel performer RPM, 1" 4 hole spacer, 3/8" insulating gasket and a 84 HO dual snorkel air cleaner....had to trim the hood insulation AND the hood bracing...but it closes.  This is an older pic and unfortunately doesn't show the hood but I'll keep looking.
84 COUGAR/90 HO, 1.7RRs, performer RPM,700DP, equal length shorties, stainless EXH ,T-5,Hurst pro-billet, KC clutch, 8.8/ 4.10s, line-lok, bla ,bla, bla.
71 COMET/289,351w heads, 12.5 TRWs, 750DP, Liberty TL, 9"/6.00s, 11.9x @112 , bla,bla,bla.

Never shoot your mouth off, unless your brain is loaded! ....I may get older, but I'll never grow up!....If you're not laughing, you're not living!  :laughing:

Carbueted Hood clearance ?

Reply #3 –
I am assuming this is only pertaining to stock hooded cars?

Darren

83 351W TKO'd T-Bird on the bottle


93 331 Mustang Coupe - 368 rwhp

Carbueted Hood clearance ?

Reply #4 –
Quote from: Aerocoupe;379114
I am assuming this is only pertaining to stock hooded cars?

Darren

 
Not at all bro I'd like to get info on/see any and all possibilities and than make a decision . My combo's going to be a .030 over 5.0 10 to 1 compression .590/.603 230/236 @ .050 solid roller Vic Jr heads 650 carb and for the beginning anyway an old torker intake I had around . Also 4.10 rear 2500 converter .

Carbueted Hood clearance ?

Reply #5 –
The 4.10 rear and the 2500 converter are in my 87 cougar now along with shorty headers and an off road x pipe with Quick flow lers . You would be suprised how strong that old 150 horse power low po 5.0 runs with this setup . I can't wait for the real motor to go in .

Carbueted Hood clearance ?

Reply #6 –
I run a 8.2 deck engine with a Parker Funnel Web intake manifold, 4150 series Pro Systems Carb, and a Moroso 2 1/2 inch drop deck air cleaner and a 3 inch filter.  The engine mounts are custom 2 1'2" tall solid steel instead of the factory 3" fluid dampened biscuits.  Everything else is standard height and I have 3/8" clearance from the top of the cleaner and the hood.
Blueprinted 306, Thumper ported Canfield 195's, TLSR Camshaft, custom motor mounts, Parker funnelweb, Pro Systems Carburetor, Tremec 3550 II, 4.30 gears, Moser Axles, Team Z custom suspension with upper relocation brackets and anti roll bar.  At the track I run M/T 26/10's on Weld Star rims.

Carbueted Hood clearance ?

Reply #7 –
Took a pic of the underside of the hood to-day that is more up to date.
84 COUGAR/90 HO, 1.7RRs, performer RPM,700DP, equal length shorties, stainless EXH ,T-5,Hurst pro-billet, KC clutch, 8.8/ 4.10s, line-lok, bla ,bla, bla.
71 COMET/289,351w heads, 12.5 TRWs, 750DP, Liberty TL, 9"/6.00s, 11.9x @112 , bla,bla,bla.

Never shoot your mouth off, unless your brain is loaded! ....I may get older, but I'll never grow up!....If you're not laughing, you're not living!  :laughing:

Carbueted Hood clearance ?

Reply #8 –
Quote from: QUICKSHIFT;379052
Edel performer RPM, 1" 4 hole spacer, 3/8" insulating gasket and a 84 HO dual snorkel air cleaner....had to trim the hood insulation AND the hood bracing...but it closes.  This is an older pic and unfortunately doesn't show the hood but I'll keep looking.

 
 I love your setup  . It looks like it came from the factory that way  .

Carbueted Hood clearance ?

Reply #9 –
How's the low end with that Funnel Web ?

Carbueted Hood clearance ?

Reply #10 –
Quote from: ricktjr;379303
I love your setup  . It looks like it came from the factory that way  .

Thanks. I pray that a motor mount never lets loose while I'm standing on it!  LOL
84 COUGAR/90 HO, 1.7RRs, performer RPM,700DP, equal length shorties, stainless EXH ,T-5,Hurst pro-billet, KC clutch, 8.8/ 4.10s, line-lok, bla ,bla, bla.
71 COMET/289,351w heads, 12.5 TRWs, 750DP, Liberty TL, 9"/6.00s, 11.9x @112 , bla,bla,bla.

Never shoot your mouth off, unless your brain is loaded! ....I may get older, but I'll never grow up!....If you're not laughing, you're not living!  :laughing: